Jet-Lube CC Lube Food-Grade Lubricant: How a Semi-Synthetic PTFE Formula Prevents Washout in Food Processing

JetLube CC LUBE™ — NSF H-1 food grade lubricant built on an aluminum complex / PTFE semi-synthetic formula that locks out hot water washout, survives baking oven temperatures up to 400°F (204°C), and keeps your food processing equipment running between scheduled shutdowns. If your current grease is migrating, melting, or failing USDA audits, this episode breaks down exactly why CC LUBE™ belongs on your approved lubricants list. Full product detail at https://www.pe-energy.com/product/70529-cc-lube/ Hot water washout is the number-one grease killer on food processing lines — and the aluminum complex thickener in CC LUBE™ is engineered to resist it where lithium-complex greases fail. Pair that thickener with PTFE and a white oil / synthetic base fluid blend and you get a PTFE multipurpose lubricant that stays in roller, pillow block, needle, and plain bearing cavities even under aggressive CIP spray-down cycles. The dropping point hits 500°F (260°C) per ASTM D-566, so there is no melt-out in high-heat cooking zones. The EP and wear numbers hold up under real load. Shell 4-Ball testing per ASTM D-2596 returns a weld point of 126 kgf, a Load Wear Index of 25, and a wear scar diameter of 0.7 mm (ASTM D-2266) — solid moderate-EP performance achieved without zinc or heavy-metal additives that would disqualify the product from food-contact service. Base oil viscosity runs 100–150 cSt at 40°C and 14.3 cSt typical at 100°C (ASTM D-445), NLGI grade 1–1½, penetration 285–315 at 77°F per ASTM D-217. That viscosity window covers the broad bearing mix found in bottling, conveying, and packaging lines. Oxidation stability directly controls your relubrication intervals. ASTM D-942 testing shows a PSI drop of less than 5.0 over 100 hours — strong oxidative resistance that extends the interval on conveyors and packaging equipment you cannot afford to pull offline. Copper strip corrosion rates at 1A per ASTM D-4048, confirming CC LUBE™ is non-aggressive to the copper alloys common in food machinery. Anti-bacterial additives are built into the formula to suppress bacterial culturing on wet surfaces — a practical advantage that goes beyond the certificate. Regulatory compliance is complete and dual-layer. CC LUBE™ carries NSF H-1 Registration #048221 and conforms to FDA CFR 21 Section 178.3570 for incidental food contact — the baseline required by Federally Inspected Meat and Poultry Plants and third-party schemes including SQF, BRC, and FSSC 22000. Spec it into your RFPs with confidence. For baking oven conveyor belting, the flash point exceeds 450°F (232°C) per ASTM D-92 and autoignition tops 500°F (260°C), eliminating lubricant ignition as a safety or insurance concern. Operating range: 0°F (-18°C) to 400°F (204°C). Compatibility is wide — contamination risk is low. CC LUBE™ is documented safe on Viton, Neoprene, Buna, and HSN rubber elastomers; nylon and vinyl plastics; stainless steel; and will not stain cotton, polyester, or Mylar fabrics. The clear, colorless appearance means any over-application shows immediately during line walkthroughs and audits. Wholesale orders scale from a single spare container to full-facility rollout. Browse the complete JetLube lineup: https://www.pe-energy.com/brand/jet-lube/ Resources https://www.pe-energy.com/product/70529-cc-lube/ https://www.pe-energy.com/brand/jet-lube/ https://gravatar.com/peenergymx https://gravatar.com/taylorindustrialequipment