Bandsaw Height, Darkening Cherry, Drill Press or Router? and MORE!!!

This Episodes Questions: Brian's Questions: I'm so curious about the Laguna bandsaws that Guy used at work. Long time listeners of this podcast could easily believe that Laguna bandsaw tables are at knee height and unusable. But I have a Laguna 14/12 and the table is at 35", which seems really normal, and I'm pretty tall. All the other Laguna saws I've used or been around seem about in the same range. Is this not normal? Is Guy freakishly tall? Or an advocate of chest height bandsaw tables? Parker I haven't felt like my woodworking really justifies a jointer yet.  I don't generally mind using a planer sled to get flat faces and a jointer sled on the table saw to edge joint boards, but I've never tried to use those workarounds on long stock (over 4'.)  With that being said, this dinner table project that is looming ahead of me seems like it might be the moment to finally take the plunge and buy a jointer. Do you think its possible to get the table top glue-ready without a jointer? I trust my planer sled to get flat faces, but I'm wondering if you think edge jointing such long boards is possible with an extra long table saw jointer sled jig.  Any tips on milling and glue up for this table top would be very appreciated.  Part 2: Or maybe you guys can give me the nudge to consider this dinner table project as the moment to finally buy a jointer.  I suspect that a bench top jointer wouldn't give me much (other than efficiency) over the work arounds that I already use for milling.  Do you have any recommendations for a first jointer? I don't have major space limitations but I do like to save money, so I'm curious if you guys would send a case like mine to scour craigslist or facebook marketplace for an old delta 6". Thanks as always for your contributions to the woodworking community!  It can't be said too often: you guys really do make the best woodworking podcast there is!! Evan Guys Questions: Hey guys, I’m new to woodworking, really enjoying listening to the podcast!! I have a question, would you guys be able to go over what you use your 3/4, 4/4 etc lumber!? I often think that you need thick lumber for projects. I don’t have a project in mind but I bought some rough saw lumber that I plan on using for trim in the house but I bought enough to have plenty left over. Ivan I want to build a cherry coffee table for my house. We've got a couple of cherry pieces that I've made. I really love watching them darken and get more beautiful with age. The other pieces I've made don't really see much direct blasting sunlight so the process is subtle. The coffee table however, would get some direct morning sunlight every day (or at least for the three months of the year that we get direct sunlight in the pacific northwest). I'm worried about uneven color change and sun shadows on the top where there would be decorative objects or books or things left in one spot for a period. If I pre-darken it by leaving it in the sun for some hours or a day or two will that slow the process enough to alleviate this? If so, should I do it before or after finishing? Is there anything else I can do to help, besides not putting stuff on top of course? Parker Huys Questions: Hi Fellas, I recently purchased a horizontal crown bit ( ref: Yonico 16172 ) to apply a soft dimple to the drawer faces on my tool cabinet. I will be recessing the drawer pulls within them. The challenge that I'm facing is that the drawer faces are a little small, 5 1/2" x 3 1/4", and without being overly creative on work holding, I'm not seeing a safe way to plunge the face onto the bit in my router table, or plunge the bit into the face with a hand held router. My plan is to chuck the bit into my drill press and use that to apply the cut.  What experience, tips, or words of advice might you have in using a drill press with router bits? I have a Grizzly G7943 which only spins up to 3050 rpm. Thanks in advance, and for all that you guys do for our craft of woodworking! Justin I have a 16' PVC board (8" tall * 3/4" * 16') that needs an edge profile added . The edge profile needed is to mimic a skirt board (this board installs at the bottom of an exterior siding). I purchased the 6" wide boards with the profile cut by the mfg, but they did not have an 8" so I'll need to cut this myself. The profile is a 1/4" tongue that is 1" in length with a 45 degree cut underneath. This allows the skirt board to slip underneath the bottom row of siding (the 1/4" section) and still have the rain/water drip off (the 45 degree portion). How would you cut this profile? I am thinking on a router table, but appreciate your input. Thank you, Mark Moeller