Box Glue-Ups, New Shop Build, Which Tablesaw and MORE!!!

This Episodes Questions: Brians Questions: Thank you for your awesome podcast! I recently started listening and am still working through older podcasts while staying up on your bi-weekly episodes.  I would describe myself as a longtime hobbyist who has built some basic furniture but who still has much to learn. My current project is setting up my workshop in one car space of a 3 car garage after having moved back to California from Colorado.  We’ve been back for over 3 years, but holding down a demanding full-time job and getting 2 kids through grad school has kept my wife and I pretty busy and has left little time for hobbies. Since I don’t have any specific projects in the works besides setting up my shop, my question is a little broader.  Curious to learn more about your thoughts on hand planes.  How much of your woodworking repertoire includes the use of hand planes, what types of hand planes do you use the most and for what types of jobs do you use them?  Or, do you completely omit hand planes from your woodworking arsenal? Thanks again for the great podcast. Best regards, Darryl Noda (Wildfield Woodshop) Thanks once again for putting out the most helpful woodworking podcast I listen to!   I'm making a lot of small boxes, many of which I make as one piece and then cut the lid off with a table saw or bandsaw.  How do you deal with glue squeeze-out on the interior corners of such boxes, when you can't access it until after you cut off the lid?  My current methods are to pre-finish the interior sides of the box, so the squeeze out doesn't affect the finish, or else to use painter's tape at the corners.  The pre-finishing works decently but requires a lot of forethought and has some limitations; the painter's tape is a pain and doesn't work all that well.  Another method I've tried is not caring about the squeeze-out and installing box inserts to cover it up.  Do you all have a preferred method for dealing with gluing up closed boxes?  Thanks again in advance for your good advice. Kyle can you live without  a pedestal drill press? It’s handy, with relatively small footprint. But it seems like I use it exclusively perpendicular holes with Brad point or forstner bits., I could probably replace it with a drill guide like this UJK one. https://www.axminstertools.com/global/ujk-technology-drill-guide-with-10mm-chuck-106072  Thanks again for the pod, and for considering my question! Johnny    Huy's Questions:    My wife and I were on vacation earlier this summer driving from Iowa to Florida and I was board listening to the radio and she suggested I look for a podcast on woodworking. Boy was she sorry she suggested that! I found your podcast and what an informative and fun podcast!  I’ve listen to a lot of them but have not got to them all. I am  getting back to woodworking and have started a side gig and have completed a few projects for a few people and have several more to do. I’m doing tables, shelves, cabinets, bookshelves, benches, and some other smaller things. I have a pretty good shop with a pretty good tool selection. Just purchased a Sawstop PCS 175, 36” fence and I can’t believe the quality from my old Delta contractor saw. It will certainly help me up my game on a lot of things. I have a couple of questions that I hope you can help. Some of these projects are stained and others are painted. Up to this point I have just used brushes and rollers to paint and use mostly Sherwin Williams paint. The project turns out ok and my clients are satisfied but I’m ready to kick it up a notch by spraying. I’ve used a sprayer called a Criiter and while it works ok it very difficult to use on anything of size. I’m lo I recently had the misfortune of losing my shop to a windstorm/tornado. So, I now 'get' to rebuild. I plan on having a footprint of about 30 x 40 with a 10' rollup door and one man door. I have several questions so appreciate that you may not be able to answer them all. 1. What would you suggest for the interion walls? OSB, plywood or ? 1/2" or 3/4"? 2. I plan on putting my table saw and outfeed table in the middle of the shop with the other typical tools - bandsaw, drill press, router table, jointer, planer on or near the exterior walls. Do you have any suggestions as to the layout of the shop? 3. My tools were all rescued thought they undoubtedly suffered some water damage and I won't really know the extent of the damage until the new shop is up and the tools are unloaded from the storage container. Any thoughts on how to deal with potentially water damaged tools? 4. I plan on getting a new dust collector as my old one didn't make it; a wall fell on it and I don't think it can be repaired. Any suggestions for a new one? I plan on plumbing in pvc piping to each of the tools so would like to have something pretty robust. 5. What would you suggest for shop height? My last shop was formerly used as a barn so had a 15' or so height; I don't think I need anything that high but am thinking about 10 or 11 feet here. 6. I plan on adding a cnc to the shop at some point in the future. What are your thoughts about placement of this machine? Should be against a wall or ? Thanks very much for your outstanding Podcast. I really, really enjoy it and learn lots every time I listen. Ron Hi guys! I love the podcast and have almost caught up to the current episode. You guys really keep it to the topics, which is great!! I am currently working in my garage shop that is 18ftx14ft. I currently have a 10 inch job site table saw and I'm ready to upgrade to a cabnent saw. I am liking the Alpha HW110LC-36Pro but don't know much about them. I am also considering the Grizzly G0899. What are your thoughts on these saws. Thank you all and keep up the great work on the podcast!!! David Caraway