Cabinet Construction, Tablesaw Jigs, Keeping Your Fingers Attached and MORE!!

Guy's Questions: Good afternoon Gentlemen, Thank you for your podcast, I really appreciate it, and you fellows. Long story short, I am a re-engaging woodworker after taking a 20 year hiatus. Due to life requirements and work travel frequency, I was unable to keep up my hobby. I now have the time (and hopefully will NEVER have to fly somewhere for work again) to start anew. Things have changed quite a bit in past couple decades, and so have my interests in terms of wood working. Over my hiatus, I sold some of my equipment in hopes the machines would be used instead of sitting idle and it is time to re-equip my shop needs with eliminated tools and new needs. My tool requirements are also much different today, then they were 20 years ago. One requirement I now have is a drum sander. I don't have the desire to rotate any work (key point), and want to acquire a machine that fits my specific needs, thus an 18" capability is perfect for what my new woodworking interests require. I also refuse to take any advice from boob tube woodworkers recommendations, as it seems that 90% of the creators I find may have started out providing woodworking content, but they mostly all just become prejudiced tool reviewers who conflict each other based on who is giving them free tools or paying them. I have lost a lot of respect for some woodworkers on YouTube who used to be considered by me as inspirations in their early YouTube careers, no longer. With that said, I have trimmed my interest list down to a Jet 1836 and Supermax 19-38. I imagine some or all of you have had experience with both, and would like your feedback. I am not currently considering models with moving/height adjustable belts such as the shop fox/grizzly, however if you have anything to add on those, it would be nice to hear. Glad you have a new host, it seems like he may be a great fit for the podcast. Well wishes to all of you, and Guy, I hope your health is well. Kurtis Van Kampen You fellas have filled my head with hours and hours of information. You’re truly the best Podcast I’ve found. So before Guy’s head begins to swell, on with the question. I’ve started watching Nee Yankee workshop again now they I actually have a 520 sqft shop to work out in. In the first season Norm used what he called a panel cutting jig for the table saw. The fence of the jig was located on the blade side rather than the operator side like the modern crosscut sled. This jig is dead simple being made of only three boards. I had big plans to make a modern crosscut sled (not the aircraft carrier) with all the bells and whistles. Now I’m completely rethinking my next table saw jig. Since Guy (like myself) is the only one of you old enough to remember the first episode, this should probably be HIS question. Keep up the great work fellows. I appreciate what each of you bring to the table. -Bryan   Huy's Questions: I’d first like to say that I listen to a bunch of other woodworking podcasts as well, but of all of them, yours has the lowest level of useless off-topic banter. Keep up the good work. I have a question about the usage of my shop air cleaner. It’s a Jet AFS-1000B, and my ceiling is only 7’6”, so can’t hang it from there. So I have it on a roll-around cart. My shop is 13’ x 17’. I don’t have a central dust collection system, but for the following tools I hook up my shop vac to the tool: table saw, planer, drum sander, router table and random orbit sander. I also have a circular saw, a handheld router, a jigsaw, a drill press, a belt sander and a palm sander. My question is, for which tools should I be turning on the air cleaner, and on which setting? (it has low, medium and high settings) And how long should I keep it on for after the tool has been turned off? Thanks. Steve My perception is that the people who seem to get hurt the most are woodworking professionals who become too comfortable/familiar with machines. Is that a fair assessment? [I am a hobbyist woodworker.] FYI, on 3 I am just asking for a comment on my observation. Have a great day Chuck   Brians Questions: First, love the podcast and thank you! Question: I’m building a 28 foot table. I’m thinking that I will essentially build 4 table tops and connect them with ‘double breadboards’ with runners between the tressels (5). Thoughts? Back story: I am a veteran and I run a program that addresses PTSD, Substance Abuse and homelessness in the the veteran community. An essential component is that the veterans cook meals and eat together and as the program has grown, there is an assortment of tables in the house and I want too big a build one. I am an average woodworker and I can do the basics. It doesn’t have to be piece of art, just chunky and uniform. Also, there’s not a big endless budget so I am doing what I can. The vision: I fhave to build it in my garage and put it together on site. 28 feet long, 38 inches wide (the space dictates it). The only way I can work out the jointing is a double breadboard end that joins each section. I thought about end jointing with dowels alternating the lengths of the boards so there was no single joint across the length of the board which was quite the puzzle to figure out. 5 trestles essentially spaced under the middle breadboards with 2 runners supporting the table between legs and one runner connecting the legs 1/3 up from the bottom of the leg. Craig laseur Hi Guys, I love your podcast. I have listened to every single episode! Please keep them coming! I was listening to Episode 114 about the domino tips and I am now thinking of completing my kitchen cabinet project using dominoes instead of pocket screws for the cabinet construction as I already own a domino. I was curious as to how Brian prefers to assemble cabinets. I have already watched Guy's videos! ;) Do you use the domino? How do you go about end panel construction? How do you finish your cabinets? Any tips you can provide is greatly appreciated! Thanks, Natasha Round Lake, Ontario, Canada