Skip to content
Episode 212: Improving Measurement Through SOPs and Training with Weldon Wright episode artwork

Dec 28, 2021 27 min

Episode 212: Improving Measurement Through SOPs and Training with Weldon Wright

from Pipeliners Podcast Hosted by Russel Treat

This week's Pipeliners Podcast episode features Weldon Wright, the General Manager of Gas Certification Institute (GCI), discussing how to improve oil and gas measurement through the use of measurement SOPs and training. In this episode, you will learn about challenges in measurement related to RNG and hydrogen, the importance of measurement SOPs and training to get measurement right, and being aware of how changes to contracts and tariffs affect measurement. As a bonus, Weldon and host Russel Treat discuss the new Oil and Gas Measurement Podcast that will be launching soon on the Pipeline Podcast Network! Listen until the end for a preview of the new podcast hosted by Weldon. - Access the show notes and full episode transcript at PipelinersPodcast.com.

Episode details come from the podcast's RSS feed.

Embed this episode

Ready to play

Episode 212: Improving Measurement Through SOPs and Training with Weldon Wright

0:00 27:53
of matches

Transcript Auto-generated, may contain errors

Welcome to the Pipe Liners Podcast, episode 212, sponsored by Inter-SYS Corporation. Providers of Poins, the Pipeline Operations Excellence Management System, compliance and operation software for the Pipeline Control Center to address control remandagement, SCADA, and audit readiness. Find out more about Poins at intersyscorp.com. Listening to a lot of great stuff from the Pipeline Measurement Group, and mainly that it seems like the industry feels like we're a little bit behind the curve on some of this RNG, a renewable natural gas, and probably that extends into the concerns over hydrogen, as people try to figure out, hey, how do we measure this accurately?

How do we control it accurately? And just what do we do with it in some cases? What are some of the challenges with renewable natural gas that got talked about at the AGA? Well, probably the biggest challenge is the thing we don't want to talk about.

This used to be called biogas. It was the thing that not many people produced. Those that produced it were sending it into a midstream system, a gatherer that knows how to pre-process natural gas was handling this stuff and making sure what went down to the pipelines was true pipeline quality spec. Yeah, what does that mean pipeline quality spec?

For those that don't know? Well, it depends upon whether you're talking about RNG or what used to be pipeline quality gas. In other words, contaminants that don't burn have been removed. There's no oxygen in the product, and it doesn't have a lot of contaminants that would foul up engines or boilers or are your home furnace.

Also, it means that you've got pretty tight control over the BTU content and the entrained liquids, because that all messes with your home appliances. Absolutely, not only home appliances, but industry also. And industries become very, very used to having a consistent quality, consistent BTU product delivered to them. RNG kind of changes some of those rules.

So companies that have never had to worry about the BTU once gas brought into their system now are looking at it, because RNG is being brought into the system, sometimes right in the middle of distribution systems, very close to commercial and residential customers. So a lot of new monitoring and lot of new control is needed. So that's a really, that's a pretty good segue, because I know that hydrogen was talked about a lot at the AG. It's good segue for what I asked you to come on to talk about, which is improving measurement through SOPs and training.

So I think I want to ask this question. I think we talked about this the last time you're on the podcast, but for me, it's always a good segue when you talk about measurement. And that's this. What's the hardest part of getting measurement correct?

The hardest part of getting measurement correct is defining what correct is. Here in the US, we're not regulated on how we do measurement. In general, we're not. It's done through contracts, through tariffs, and most of those reference industry standards.

But even with all of that, what means correct in their particular term? We've got to know the contractual terms. We've got to know which standards are referenced before we can say we've got it correct. Once we know what the definition of correct is, then we can start figuring out how we do it.

Yeah, I think that's extremely well said. Well, then, the interesting thing, and I'm thinking about a big issue that our industry had a number of years ago when we first started bringing shell gas into these gathering systems. And the focus historically had been on, well, let's deliver the gas to a particular BTU. The delivery of that gas to a BTU was complicated by the fact that this shell gas was extremely liquids rich, which meant I'm delivering the gas to the contract requirement.

But I'm not really delivering gas that can be used at the burner tip because there's problems with these, I had too much high BTU and trained liquids per relative volume of the gas. So it's interesting, because this whole idea about what correct is got shifted because all of a sudden people started going back and adjusting their tariffs and saying, well, wait a minute, I need it to this BTU, but I need no more than this amount of the heavies. And so that's a little bit of what's being seen with the RNG push that is with more and more RNG coming into systems. And that's where the term interchangeability comes from.

And interchangeability seems to be somewhat code for air gas is not quite compliant. How do we get into your system? So the RNG, in most cases, is having to be run through small treating facilities or filtering, they're trying to get it up to contract spec. But in that world, you have really, really bad gas that came from a landfill or from digesters in a city wastewater treatment plant, and they're trying to clean it up to pipeline spec.

But no pipeline can allow all of the gas they receive across their entire pipeline to always be at the very bottom of that specification. So that inserts some challenges, how much gas can we take at the very bottom of that spec? And since more and more and more gas is coming into the system that way, as opposed to conventional natural gas sources, we're seeing companies distribution systems and pipelines having to reconsider and possibly rewrite their specs and their tariffs to better control and work with that so we can successfully get the screen energy into our system and to the end customers without causing problems in those customers. Yeah, so that's actually a great, again, it's a great segue because my next question was, well, what ought to be in a measurement standard operating procedure?

So I'll just kind of make this assertion, let you speak to it. I would say that the first step is, I have to define what I'm looking for in terms of measurement, not just volume, not just energy content, but also what are the constituent properties, those how clean and proper is the gas and the way it's put together. Correct. So that all goes to how I'm going to do my measurement, right?

Right. And those SOPs, they need to begin with what are these standards and the regulations and contracts that we intended on our gas custody transfer to be held under. So really, to me, the first place you start with writing SOPs is to understand what do our contracts require and or our tariffs require. And if it's BLM properties in the US, what do federal regulations require?

Once we know what what those requirements are, we can begin to coin our SOPs around what's required to meet those standards and are those regulations. And from that, we talk about the type of equipment that we'll need in our SOPs. We talk about the processes and procedures that we use. And of course, processes and procedures gets us to the point of what training does our folks have to have in order to properly implement those SOPs.

Yeah, so it starts with understanding your contracts and tariffs and making sure they're appropriate for your operation. And then it moves to, okay, so how are we going to measure? And then that's equipment, processes and people. And then, you know, your SOPs have to address those three things and then you got to build competencies and the people to be able to operate the SOPs.

And that gets to hold the whole question about training. So what kind of training is required or maybe a better way to ask it, what's the training that often gets missed? Well, this almost gets to be a soapbox item for me because the training we don't want to have is Bubba rides around in the truck, right? Bubba may be a great guy.

He may know a lot about measurement, but we need some fundamental knowledge set up for these people before we start riding around from the job training. So I maintain that we need for our new hires and measurement, our transfers from other departments. We need those people to have a thorough understanding of the fundamentals behind measurement, whether it's crude or gas, right? We need to understand the calculations.

We need to understand physical properties of our product. And we need to understand how those pieces fit in to the procedures we'll use with individual pieces of equipment, individual manufacturers products, and the software tools that we use. So starting again with that basic fundamentals, and that includes definitions, basic knowledge, once we have that, then we start to add training for the specific flow computers, the specific meter types are installed. We look at vendor specific and software specific training.

We look at what's required to do the quality analyzing the BTU, heating value, the specific gravity, all of those pieces only come to place once you understand the fundamentals well enough to talk about it. So we get those fundamentals out of the way, then we start the vendor specific device specific training. And of course, OJT is a big part of that. But OJT needs to be done under relative control situations.

OJT does not take place in the middle of a blizzard when you're trying to re-light it for pilot lighted down, right? OJT takes place under normal field operating conditions where people are not stressed, where they're in a reasonable environment that they can think about what they're doing, not the big fire that's running in the plant next door. Yeah, that's a really good point. And you covered that kind of quickly.

But you think about what part of that often gets missed. And I think the part that often gets missed is the fundamentals. Absolutely. Right?

Because most people that start in measurement, they're doing something pretty routine, pretty simple. They're running around and they're checking as found, as fast as they're left and doing calibrations. And that's a big part of what you've got to be able to do that and do it consistently and do it well. It's a big part of measurement.

But that's a relatively simple task. And I can do that without necessarily understanding a whole lot about how a measurement system operates. But when I start getting into the questions about, well, how come my metering doesn't balance, how come my number doesn't match my Interconnect Partner's number, or how come the volume coming into this gathering system and matching the volume coming out, that all sudden becomes a very different level of knowledge. I need to be able to do that.

I agree with that Russell, but even some of the very basic task, need that fundamental knowledge. Also, one of my favorite examples of this is a relatively new technician. He'd been working for a company for about eight years in compressor maintenance, got moved over to measurement. He thought that was the dream job.

Again, he'd been around the pipeline in the operations for many years. They put him in the truck. He went around, he learned to do the job, he learned to do meter calibrations, he learned to do testing. And he was pretty good at it.

But you know, we rarely are in a situation where we have a lot of people, more people that we need to do the job and folks just standing around, right? Everybody's pushed for time, doing more for less. This individual who remained nameless, he was out there looking at the procedure they had him doing for collecting samples. And that procedure took a long time and it required his attention the whole time he was doing it.

He figured out that it was real easy to cut that back a couple steps and he could save 10 to 15 minutes on ever sampling collected instead of going through this very lengthy fill-in purge process on this low pressure well. He thought in his mind and in his heart, he was saving the company money and doing a good job. In effect, what he was doing, because he didn't understand the fundamentals and didn't understand why the procedures called him to do what he did, he ineffectively was pumping up the BTU value of ever sampling collected about 20 BTU's. That's the small thing.

No, it's not. So, while I agree that, many of the tasks don't require fundamentals knowledge day in and day out, not understanding those fundamentals really is a key. So, again, once we have those first, then we start going through the training on specific procedures. How do we meet our SOP requirements for frequency of testing of the procedures being used, and then we also can get into vendor-specific training with specific devices?

Yeah, well, that again, that all makes sense to me. So, I want to talk a little bit about diagnostics. So, what I mean by this is when I'm doing the, all the kinds of things that would typically be reserved for a measurement engineer or a consultant to look at where I'm trying to resolve an imbalance or some other kind of problem on a system. What's the level of training I need at that point?

The level of training you need to impact that type of problem is relatively small. It's that understanding of the fundamentals and understanding of your SOPs. But then, if you want to get into the hardcore diagnostics, it definitely takes something that really can only be gained through experience, Russell. But the pieces you're looking at there is understanding what might be presenting biases on the system.

And you would ask earlier about what does it take to get measurement correct or right? One of the biggest tools to knowing whether your measurement is correct to begin with is going to be sound system balances, intake and dispositions, L&U reports, whatever your company calls them. Having good balancing that's watched and maintained on a regular basis is one of the quickest ways to pick up new problems. And then, by looking at those balances, which does get into advanced measurement, right?

Let's look at those balances and let's try to determine where the excursions are coming from on a daily or even an hourly basis. It's being able to look at the procedures and understand why do we do procedures in a certain way and understand if we don't do them in that way, how do we get the type of bad results that we have? So understanding what errors and failing to file the procedures can cause is one of those key things and being able to diagnose the problems and come up with the solutions. Yeah, I think it's really well said well, because at least in my experience in this domain, one of the first things you do when you're trying to understand what's going on is the first thing you do is you look at all just kind of basics and try to get understanding of the numbers and how they're being brought together.

Then once you have that, you're looking at well, what are the procedures and are they being followed? And a lot of times what you find out is when you start getting into the nitty-gritty details of something, the procedures are missing. The procedures may be too high level or they're too generic or they don't address this specific case or the specific kind of device or equipment you're using in the field. And that becomes a real problem.

Exactly, exactly. You touched on a couple of really important parts there. And I agree with all of them. To get out there and to try to look at those kind of items, being able to, what's the right word for it, being able to objectively look at the procedures doing being used.

And with reference to what you said about procedures being too generic, I see that all too often. I've seen measurement procedures that called out, we will measure according to AGA3, we will measure according to API21.1, and that's almost the limit of what they say. Those are complex standards, there's a lot of stuff in it, and any given operation is not going to have measurement take place under all of the possibilities that happen under all of those standards. So that's where SOPs written that specifically reflect your contracts and your tariffs become important.

But not only do we have a set of SOPs to begin with, your SOPs, like you're training, cannot be static. You need to constantly be watching the standard your SOPs reference. You need to be constantly watching for changes in how your contracts and your tariffs work, what changes in product quality may take place. You need to be watching all those things and make updates to your SOPs and your training to match those.

And we both know in today's age, the rate that hardware is changing and the software that supports that hardware is almost beyond what Jack and Fathom when I got into this industry 30 plus years ago, right? Just the amount of equipment that we have available to us and the complexity and the capability of equipment. Absolutely. I mean, it's grown exponentially even in the last 10 years.

So, well, then we have a big announcement to make. We are putting together a new podcast and welding is going to be the host. It's going to be the oil and gas measurement podcast. This is something I've been wanting to add for a long time, probably because I started out in measurement and I know a lot of people in that area of our business.

So, I'm really excited about this. And I know welding is too. So, what do you hope to accomplish as we roll out this new podcast on only gas measurement? Russell, I installed my first flow meter back around 1985.

In the last 37 years, there's two things that I can now say for certain about measurement that are absolutely true. One of which is the more I learn about measurement, the more I realize I still have a lot to learn. And the second is that disseminating measurement knowledge is not always easy, especially for new folks in our industry. There is so much out there, so many different things you may need to know and not a lot of places that pull it all together.

So, what I want to accomplish with this podcast is I want to pull together those tidbits of information from all the different areas of measurement and started getting out there. So, people have better access to it. And we all know how much time you spend staring at that windshield. If you can listen to a podcast while you find out about the latest AGA or API updates, if you listen to a podcast talking about methane emissions and the new advances in detecting leaks as well as how we can estimate volumes, if you can learn information about some of the latest technology coming out or what the problems are relating to green energy with RNG and hydrogen, if we can provide you a little snippets of information while you drive side to side, I will consider it a grand success.

Well, I'm with you. I think measurement is one of those subjects where by the time you're current and all the disciplines, you've become out of date in the discipline you started with. So, if I start looking at, I'll just, I start working with gas orifice plates and then I move from orifice plates to turbines and then I work for a while on choreoallus meters and then I work on some analytical equipment and then I come back to orifice meters. By the time you make that circuit, you come take a deep dive into orifice meters, not car anymore.

It's just the nature of things. And that's kind of true throughout our industry. So, being able to help people stay current I think is really important. And I think the other thing too, is there's so many things that can happen to cause your measurement to go askew, that having a resource where you can go and listen and constantly be hearing about here's problems that occurred and lessons that we learned, that's just a huge value to the industry.

I agree, Russell. And we hope to get there with this new podcast. Like you said earlier, it kind of excited me. When you first discussed this with me, it was a no-brainer for me to dive in with both feet because it's something I'm passionate about.

So, can you give us some teasers? What are you hoping to do to talk about some of the first episodes? Well, some of the first episodes are some of the items I just mentioned earlier. We're going to have some updates on what's happening with AGA and API.

One of our earliest episodes will be an update on what's going on at API with produced water, about how we measure and how we account for produced water. We'll have Robert Ward on one of our early episodes, and he's going to talk about advances in methane leak detection, and how some of those advances can lead us to actually measuring or at least estimating measurement of those leaks. We're going to talk about data mining and statistical analysis of your measurement data to help you set better validation rules while reducing the number of nuisance exceptions you see in your measurement system. So, great stuff like that.

Well, listen, I'm looking forward to it. I'm also kind of excited that we're adding a new host to what we're doing because as much as I enjoy this, there's only so many hours in a day. And I will tell you that it'll be very interesting for you and I to have this conversation in a year or two once you've done a bunch of these episodes because I suspect you're going to learn, you're going to learn just as much as listeners as you go through and do all that. That's certainly been my experience as I've been doing this podcast.

I expect that to be the case. In fact, I'm looking forward to it, excuse to get people in front of me that I can quiz on what about stuff I need to learn. So, just for the listeners that that new podcast, we will be standing that up shortly after the first of the year. We're looking forward to getting people to listen and hearing the feedback and learning what people would like to know.

And I'm also open to any and all topics. Feel free to send in suggestions. We'll take a look at it, suggestions on topics or specific suggestions on a guest. And if you feel like you have something to share directly on the podcast, by all means, let me know.

We'll see about getting you on. So, if you want to give us some ideas, there's a couple of ways to do that. One way would be just go to the Py Pliners podcast website, go to the Contact Us page and just drop us a form. I look at every single one of those, anything that's going to be relative to the Olin Gas Measurement podcast, I'll get that right over to Weldon and he'll be following up.

You can also go to the podcast website, look up Weldon's profile page, get his connection on LinkedIn and you can link, you can reach out to him directly on LinkedIn. So, either of those would be good vehicles for sharing your thoughts and interests and helping us put together something that be of value to the listeners. You're exactly right there, Russell. We look forward to it.

We want to deliver a product that people are find valuable and are ready for the next episode to be dropped. So, the more suggestions we get, the more powerful we can make this podcast. Well, listen, I think that's a great place to end this episode and looking forward to you having great success. Thanks a lot, Russell.

Hope you enjoyed this week's episode of the Py Pliners podcast and our conversation with Weldon. Just a reminder, before you go, you should register to win our customized Py Pliners podcast Yeti Tumbler. Simply visit pipelineerspodcast.com slash win and end yourself in the drawing. If you'd like to support the podcast, please leave us a review, either on Apple Podcast, Google Play, or wherever you happen to listen.

You can find instructions at pipelineerspodcast.com. If you have ideas, questions, or topics you'd be interested in, please let me know, either on the contact us page at pipelineerspodcast.com or reach out to me to directly on LinkedIn. Thanks for listening. I'll talk to you next week.

Frequently asked questions

How long is this episode of Pipeliners Podcast?

This episode is 27 minutes long.

When was this Pipeliners Podcast episode published?

This episode was published on December 28, 2021.

Is there a transcript available for this episode?

Yes, a full transcript is available for this episode. You can read the complete transcript on the episode page.

Can I download this Pipeliners Podcast episode?

Yes. Use the download control on the episode player to save the publisher-provided media file.