Episode 99 - Resaw Blades, Finish Both Sides?, Dull Blades From Sanding & MUCH More!

Support us on Patreon: https://www.patreon.com/woodshoplife This episode is sponsored by: Shaper Tools, makers of Shaper Origin   Guy 1) I recently discovered your podcast and it has drastically improved my hour long commute to and from work. I began making attempts at creating things with wood about a year and 1/2 ago after wandering into a woodcraft and seeing all of the beautiful exotic species in person.  I made afew cutting boards and smaller items,  but nearly gave up because my few feeble attempts at joinery completely tanked. I’m kind of a high energy/ ADHD person with almost no attention span, and woodworking just wasn’t working for me. Then I found wood turning, and  found it to be extremely satisfying, almost therapeutic. I still have a long ways to go, but I no longer feel completely incompetent and have made several decent items. I eventually hope to learn some joinery techniques and attempt some small furniture type items. I recently purchased a Jet JWBS -15 bandsaw and so far have been very pleased with it. It has a large cast iron table along with cast iron wheels. The only thing it’s missing is a brake, but since it’s my first bandsaw, I don’t miss it. This particular model, however is not carried by most of the wood working stores and very few people even mention it other than Shawn. Is there a reason why this saw is not popular? The only issue I have is that I go through bandsaw blades like water. I typically use either a green wood blade or the timber wolf 3/8” 4tpi blades and have not gotten more than a month of light use from any. Is this normal?   I cut a lot of rosewoods, ebony and dense exotic turning blanks.  I considered getting a carbide blade but they are upwards of $200 for my saw. Any thoughts? Nicole 2) Hey guys, you’ve answered a few of my questions over the years so I’m now running out of ways to say how awesome this podcast is. I just want y’all to know that it’s been extremely insightful, helpful, inspirational, and motivational (oh yeah, and funny). Woodworking is a great stress reliever for me and your podcast motivates me to keep at it, so thanks again. My question today is about how to determine the weight-bearing capacity of something you build. I generally don’t build off plans. I find inspiration from photos online and then create my own design, but this sometimes means I’m deciding how much support to give certain pieces. For example, I recently completed an outdoor bench with planter boxes on either side. I really didn’t know how much I needed to do to support the bench and the weight of those who might sit on it. It’s 4.5 feet long, so can fit up to 3 adults at a time. I’ll describe what I did and send some photos, but if there are any rules of thumb or resources you can share that would be helpful in determining the weight capacity for furniture builds, I’d greatly appreciate it. Thanks again for the awesome podcast. Billy   Sean 1) Hey guys, I'm looking to purchase a better flush trim router bit. I'm comparing Whiteside bits UDFT 5152 and the UDC 9112 from Bits and Bits with the astra coating. Other than the bit diameter, cut length, and one having two bearings. What would make you choose one over the other if the bit diameter didn't matter? Do you think the 9112 would run cooler due to the larger diameter? I plan on getting the 1/4" compression flush trim bit for small curves. Thanks for all the real world advice you give. Matt in AL 2) I'm building a console-style liquor cabinet that will have a walnut slab top. The slab is 1-1/2 inches thick, 60 inches long, and 16 inches wide. I'll be using an oil finish and am wondering whether I should apply the oil finish to both the top and bottom of the slab... or if just finishing the top (and edges, of course) is enough. It's my first time working with a slab and I don't want to screw it up! Thanks for the great show! - Dan https://www.woodshopnews.com/columns-blogs/finishing-both-sides-is-warped-thinking Article mentioned during Podcast.   Huy 1) Great show, love it! I have a small shop in Denmark, and recently I talked to a rep from Festool that told me not to sand my wood before all cutting is done, as the small sand grits would make your blades dull. What are your thought on this? Thanks, Ali @toolguy.dk 2)Hello from one of your dedicated listeners!  My question concerns a router dropping bits.  The router in question is a fairly new Triton TRA001  3 1/4 HP plunge router.  Three times now, while making a fairly easy pass, the bit has dropped out.  The first time it happened was while I was cutting a quarter inch deep rabbet on a half inch cherry panel.  The bit cut a hole in the panel and ruined it as it fell straight down onto the floor. The two other times have been while cutting a 3/8 inch deep dado through some 3/4 inch maple ply.   Any advice would be welcome.  And thanks for all the thoughtful and informed conversations about woodworking. Martin