Jointing Edges, Painted Furniture, Is It Still Handmade? and MORE!

Brian's Questions: Hey Guys! Love the podcast. Long time listener, first time asking a question! I am looking for recommendations on how to remove saw marks after ripping pieces to final width on the table saw. I recently built a couple rocking chairs for my kiddos, and was looking for a super smooth surface finish on all four sides. My solution was to joint and plane the parts on 3 sides and then rip a 1/32 or so oversized. After that I set my jointer to 1/32 and ran the cut edge back over the jointer to remove the saw. This m I recently scored a router table on Facebook marketplace for $500. Woodpecker PRL 1 lift, Incra jig ultra fence, and Porter Cable 3.25 horse router. 1, what's your favorite lubricant for threaded parts like router lifts and table saw arbor tilts? 2, Other than keeping them clear of dust so they don't over heat is there any other maintenance to extend the life of a router? They don't make the Porter Cable routers anymore so I want to keep it in top condition. - Tylerethod seems to work nicely. I am using a Jet cabinet saw and not matter how much I try to adjust it, I can never seem to get a rip without at least a few saw marks. Just looking for ways to improve my efficiency while in the shop! Thanks again Dylan.   Hey guys, You said you needed more questions so here ya go... I have a couple hundred bucks left over from my December birthday and Christmas haul that I plan to spend on woodworking supplies/tools. I keep a running wish list throughout the year of various woodworking things I "need" So there is no shortage of things I could spend it on, however I don't want to waste it. That has encouraged me to just sit on it for now and I feel like I'm at a bit of a crossroads. Do I simply save it and put it towards a big more expensive tool down the road (for example I don't currently have any kind of planer or joiner). Or do I use it to buy some of the less sexy but more useful day to day items that every shop should have (i.e. better bits, blades, consumables, jigs, etc...) For reference: At this point in my woodworking career I do mostly hobbyist/DIY level work. I have either budget or second hand versions of most basic hand and power tools and the basic bigger tools (Benchtop Drill Press, Contractor Saw, Miter Saw) I would love to delve in to the more serious side of woodworking one day, so I do have a goal of getting a planer and joiner down the road. But realistically I know if one fell down from the heavens in to my shop tomorrow it wouldn't get used immediately. Regardless of my own personal decisions I thought it would be cool to get y'alls take on what you would consider the top small ticket items that every shop should have. I think we all get more excited about big expensive tools, because frankly it's more fun, but for people like myself just getting started on this journey it can be easy to miss the basics as a result of that excitement. Thanks for being so awesome, Jon   Guy's Questions:   Good day fellas, Been listening for a while, and really enjoy the podcast. Here is my problem/question. For Christmas this past year I made a few cutting boards as gifts using Maple, Walnut and a few pieces of Purple Heart. In my design process I managed to make one of the cutting boards slightly too big to fit (on first glue up) through my Dewalt DW735 planer. In order to save some time, I just ran the piece through the table saw to get the over width down to just under 13". On the first pass through the planer, everything went as planned. The second pass through didnt go so great. At around ¾ of the way through, the planer dug into the piece and put some pretty nasty snipe into the piece. Id say around 4-5" from the end of the board, and almost 1/8" deep. What would cause that to happen? Narrower pieces that ive ran through after havent given me any snipe since. Is it due to me using the entire 13" of the cutter head? Because of my snipe issue, im really hesitant on running anything wide through the planer now. I want to experiment using some cheaper wood, but just havent found the time to do so yet. Thanks for the help. - Dwayne   Hey guys, heard you are in need of some questions from the last show, so thought I would send one your way. What do you think is the best paint for furniture that will see use and abuse? I’ve been experimenting with some different options and haven’t found anything that I think I will stick with, and I do not want to put a clear coat over the paint. Looking for something very hard and durable, as the next time I need it will be for chairs. Any suggestions would be much appreciated. Thanks!   Huy's Questions:   When does something cross the line between being 'handmade' and 'machine made'? My nephew had a CNC machine and advertised the products as 'handmade.' Is this all subjective anyways? Have a great day Chuck