Skill Development, Stabilizing Wood Defects, Flat Assembly Table and MORE!!!

Brians Questions: How do I take my woodworking skills to the next level, short of attending an expensive workshop? Up to this point most of what I've learned has been from either your podcast or YouTube videos (special thanks to Guy for all of his router table videos.) I have quite a few small projects under my belt, such as cutting boards, boxes, and a face frame cabinet. I'd like to move on to building small furniture pieces, but I don't feel that I have the skills to figure out how to design or build something of that scale without some sort of tutorial.  I'm sure there are tons of videos on YouTube showing how to build coffee tables and the like, but I don't want to just copy and replicate someone else's design. Most of the videos I've come across have also been using pocket holes and big box store lumber, which isn't really the direction I want to go. What I want to learn are the skills and techniques that go into building furniture so that I can put my own spin on them. If I tried to build a coffee table right now I'm sure it would just be a flat panel with square straight legs.  Thank you in advance for whatever suggestions and insights you are able to offer me. I appreciate all the time and effort you guys put into this show. I hope your projects are going well, and I hope that you're doing even better.. Zach Owens Throughout your time woodworking, have you ever hit a point where you lost your motivation for woodworking? If so, how did you reignite your passion and get back into it? Zach Owens Guys Questions: I appreciate the podcast and look forward to new episodes, keep up the great work.  Here is the background:  I have attached a picture of the front of my workshop. I have the Tablesaw/planer and jointer in a square with a poweratic 1 3/4 hp single stage dust collector with "turbo cone" separator:)  servicing all three using a 10 foot flexible hose with magnetic couplers on the flexible hose and at individual machine ports. This makes aligning dust collection very quick. I am very satisfied with performance at planer and jointer. I still wear an apron and safety glasses when using the tablesaw because of the dust coming off the top of the blade. I have sealed the cabinet of the saw as much as possible. I have used an over blade collector by shark guard which captures most if not all of this dust, however, I remove this most of the time because it interferes with so many operations.  Here is the question: Do you belive there would be a noticable improvement in dust collection,at the tablesaw in particular, by upgrading the dust collector to a product like an Oneida Dust Gorilla or Supercell?  I would still like to use the flexible hoses vs. hard piping to support being able to reconfigure the shop in future.  Every piece of equipment is readily movable.  Thanks, keep up the great podcast.  Dave@ Xcuse4tools Custom Woodwork  I’m a hobbyist furniture maker working in a home shop. I have several kiln-dried ash boards that have visible insect tracks and wormholes — no active infestation, just the character left behind. I’m building a benchtop seat from this material and I want to lean into that look instead of hiding it. What finishing approach would you recommend to best highlight and preserve the insect damage — things like filling the voids, stabilizing the soft areas, and choosing a topcoat — so it looks intentional and high-end rather than defective? Thank you again for the content. Catching up on old shows though I cannot locate the older shows on Spotify! Have a great week. Greg Wolf's Den Homestead  Huys Questions: Hi guys, My house came with a work bench when I bought it. It's nice and sturdy but the Masonite top had seen better days so I'm replacing it with a piece of 3/4" plywood. I just took the top off, and realized that the structure underneath the top isn't totally flat, up to about a 1/8 inch dip in some places. (picture below for reference -- it's about this uneven for the full length). I have a couple of questions: 1) How flat does this need to be? Will the plywood on top make these gaps irrelevant? I understand that a very flat top is important for assembly purposes, although I didn't really notice a problem with the old top. 2) How would you go about flattening this? I have taken down a couple of high spots with my #4 bench plane, but doing the whole table would be quite an undertaking. 3) My plan is to nail the new top on, router the edges flush, and add a coat or two of Danish oil since I have a jug of that lying around. But I'm curious if any of you would do differently. Do any of you use benches with replaceable tops? Thanks! Max My question is this.  I own a high end furniture and cabinet shop and to provide quality I prefer to build my drawer boxes from solid wood (not the bottoms those are plywood). I box joint the corner joints,  but my question is on wood expansion. 1st - when milling the sides to 5/8 thickness I sometimes end up with a 5" wide board. Usually this would cause cupping but it seems like the corner joints locks everything in place.  Would you build with wider boards or cut it into say 2-3" strips and glue back together before milling? 2nd - a lot of drawers now a days can easily be 8-9" deep and up to 14" deep for some of the largest drawers I build. With this width the expansion and contraction of the drawer box concerns me,  especially once you fix the drawer fronts. I mount drawer fronts with the standard 4 screws in each corner and haven't had issues but I'm curious your thoughts.  The drawers are finished with a few coats of water based conversion varnish.  Thanks! Jared