Ultra Durable Finish, 120v or 240v?, Taper Jig Woes and MORE!!!

This Episodes Questions: Brians Questions: Hello gentleman, thank you again for one of the best woodworking podcasts available. I recently had the opportunity to travel to Lebanon IN for a few days of training at a tool manufacturer. I won't mention the company, but I got to use a Domino and a Rotex sander for the first time..., but I digress. While I was in the airport waiting for my flight home and enjoying a breakfast sandwich, I looked down at the table and noticed the "purposeful-design" logo branded on the top. This experience gave me two questions. One, what finish did Guy and Brian use on these tables to survive the abuse of so many travelers per day through an airport? Two, during the training we sanded a piece of cherry to 1500 grit, giving a very high sheen to the bare wood. What type of technique or finish would you use on something like that? Thank you for the great podcast, and I'm sorry I didn't have time to say hi while I was in Indianapolis. I waved from the plane, but you probably didn't notice. Josh Hello fellow wood-nerds. I would like some advice on finishing. I’ve been doing a bathroom remodel. Which means I’ve spent a very long time doing non-woodworking work and learning new skills and desperately missing my shop time. I’m near the end finally and actually get to do some woodwork to wrap it up. My new floor doesn’t quite line up with the floor in the next room and the transition pieces available don’t quite suit. So I’m making one custom out of walnut. My question is: what would be a good finish? I don’t want it glossy or “plasticy” looking. But of course it will be stepped on and exposed to humidity from the shower so it does need to be durable. Thanks in advance Jason Guys Questions: This one may for Guy specifically but I'm interested in getting a 3D printer and would like your opinion on what I might want to look at. I have a total budget of around $1000 and want something that is very turnkey; I don't have a ton of time to learn how to use the machine and would like that will work for me out of the box. I'm looking at the Bambu Labs p1S; would this be a good starter machine? Thanks again for the great Podcast! Ron Brewer Hi Guys, I am hoping to eventually upgrade my table saw from a jobsite saw.  I have heard a little bit of discussion about the advantages of an induction motor over a universal motor but I was wondering if you could provide some insight about voltage for a table saw.  Obviously higher power is available with table saws that operate on higher voltages but as a hobbyist I am wondering how much power I actually need.  I do make some cabinets and furniture as well as smaller projects. So here is an assortment of questions that are perhaps intertwined: Is the increase in power with a 240V saw worth it?  I would also have to get new electrical added to my garage.  Is the type of motor related to the voltage?  In your opinion are table saws that can be rewired from 120 to 240V a viable option? Would the power actually change with the rewiring?  Are there any other considerations that I am not thinking of? Thank you all for your insight. Brad Huys Questions: If you're installing a herringbone floor, do you need to think about chatoyance, in addition to colour and grain pattern, when you're laying out the pieces? Do you want all of the pieces to be oriented to have similar chatoyance? Lauris Hello Guys, I listen to your podcast while driving to and from work.  I really appreciate that you stay on track and offer several opinions regarding woodworking without the cackling and inside jokes, poor microphone control etc that other woodworking podcasts seem to have. I build a lot of Shaker style furniture with tapered legs and built my own taper jig, a sled which clamps the leg at the desired angle with the widest part of the cutoff leading into the blade.  This has worked very well except that occasionally, the wedge that is cutoff tips into the crack between the saw blade and the insert, jamming and sometimes tripping the saw's overload protection.  I have cut a brand new table saw insert with the intention of creating as close to a zero clearance slot as possible but it still is wide enough for the sliver edge of the taper cutoff to drop in.  How have you avoided this in the past?  Would a reverse orientation of the taper jig be safer such that the thinnest part of the cutoff is cut first and therefore at the back of the blade and the thickest part is the last part cutoff?  Thank you! Don