All Episodes
PCB Chat — 250 episodes · page 1 of 3
PCB Chat 162: HDP User Group Annual Update With Madan Jagernauth
RM 199: Good Adhesive, Bad Bond: The Hidden Causes of Adhesion Failure
PCB Chat 161: Chris Parker Discusses Case Study on Dielectrics and Thermal Management
PCB Chat 160: Tom Kastner on M&A Trends and Global Manufacturing Challenges
RM 198: Sean Patterson on Making Al Useful in Manufacturing
PCB Chat 159: AJ Cooper and Itera Aim to Retire the Respin
PCB Chat 158: Wally Rhines on the Latest ECAD Market Data
RM 197: Closing the Gap Between Validation and Reality
RM 196: Dr. James Maisiri on Responsible Technology Adoption
RM 194: Why Post-Reflow Cleaning Is Becoming Mainstream Again, Part 2
PCB Chat 157: Tomachie's CJ Clark Discusses AI-driven Schematic and Test Analysis
RM 193: Why Post-Reflow Cleaning Is Becoming Mainstream Again
RM 192: Why PCB Revision Errors Are a Hidden Reliability Risk
RM 191: Why Maintenance Is Finally Getting a Seat at the Table
PCB Chat 156: Lauren Waslick and Kristen Aguiar of Newgrange Design
RM 189: Predict, Prevent, Produce: RoviSys' Bryan DeBois on Manufacturing's Al Future
PCB Chat 155: Breadboard's Nemanja Jokanovic on Automating BOM Management
RM 187: An Academic Look at Al in Electronics Manufacturing: Where It Works, Fails, and Why It Matters
PCB Chat 154: Wally Rhines on the Latest ECAD Market Data
PCB Chat 153: Karen Burnham on Taking the Pain out of EMC
PCB Chat 152: Mike Buetow on the Cadence Acquisition of EMA
PCB Chat 151: Scott Bright of Cadstrom IO
RM 185: How Accuracy & Force Compliance Contribute to Better Quality & Reliability, with Michael Sivigny
PCB Chat 150: Wally Rhines on the Latest ECAD Market Data
RM 184: Advances in Dispensing Automation and Thermal Management with PVA’s Jon Urquhart
PCB Chat 149: Maggie Frachioni on the Evolution of a PCB Designer
RM 183: A Reliability Matters Podcast Year-End Reflection
RM 182: How to Work Effectively with your CM - with Daniel Stanphill & Sean Kincaid
RM 181: Working with Contract Manufacturers - with Raymond Novara
RM 180: Low Temp Soldering for a High-Reliability World
PCB Chat 147: Matthias Wagner of FluxAI
RM 179: Indium's Ross Berntson
PCB Chat 146: The Latest EDA Market Results
RM 176: The Chemistry of Reliability: Choosing the Right Solder and Flux
PCB Chat 147 with Margaret Upshur of Mobius Materials
RM 177: Humidity: Small Cause, Huge Reliability Risk with Viktoria Rawinski
PCB Chat 146 - Stephen Chavez on PCB Design Trends and Needs
RM 175 - SMT War Stories with Phil Zarrow and Jim Hall
RM 173: Reliability as a Service: How ChargerHelp! Keeps EV Charging Running
PCB Chat 145: David Schild on Congress Priorities
PCB Chat 144: The Latest PCB Design Software Market Trends
RM 172: Steering ERP Projects Back on Track with Chintan Sutaria
Cofactr on Supply Chain Execution
RM 171: Pick & Place Machine Selection and Optimization
RM 169: On the Road - Soldering
RM 168: On the Road - Electronics Assembly
Chris Banton of EMA Design Automation on Board Optimization
PCB Chat 143: Frank Mullaney and Emma Hudson of iNEMI
Tom Britton and Nataliia Matsiuk on an AI Solution for PCB Manufacturing
Robert Byrne of Allspice
RM 167: Meet the Press: A Conversation with PCEA President Mike Buetow
PCB Chat 142: The Latest PCB Design Software Market Trends
RM 166: Electronics: Down Memory Lane and a Vision for the Future
PCB Chat 141: Integrated Library Management and Component Procurement
RM 163: Sebastian Schaal of Luminovo on Supply Chain Management
RM 162: Battery Selection and Safety Best Practices with Alex Norman
PCB Chat 140: Kenny McGee on Component Circularity
RM 161: AI-Based Inspection Technologies with Priyansha Bagaria
The Semiconductor/Packaging/PCB Technology Stack
The Electronics Supply Chain and How Companies Can Adapt
RM 160: Opportunities and Challenges within the EV Industry
PCB Chat 139: PCB Design Software Market Analysis with Wally Rhines
PCB Chat 138: A Look at PCB Industry Legislation in 2025 with David Schild of the PCBAA
RM 158: D-Code Podcast Interview
RM 156: An Introduction to Flexible Circuits with Joseph Fjelstad
RM 155: Ultra HDI Panel Discussion - Recorded Live at SMTAI
RM 154: Thermal Profiling Best Practices
RM 153: Contract Manufacturing Best Practices with Adrian Leal
PCB Chat 137: The Q2 PCB Design Software Market
PCB Chat 136: Jim Rathburn on UDHI Using LCPs
RM 152: High-Reliability Solder Paste Selection Best Practices
PCB Chat 135: Duncan Haldane of JITX
RM 151: Optical Inspection System Best Practices
RM 149: AOI and X-Ray Best Practices
PCB Chat 134: Zachary Feuerstein on Supply Chain Management
RM 149: SMTA International 2024
RM 148: IPC Apex Special (Part 3 of 3)
PCB Chat 133: Wally Rhines on the PCB Design Software Market
PCB Chat 132: David Schild of the Printed Circuit Board Association of America
RM 146: IPC Apex Special: Soldering and Inspection
RM 145: Designing Electronics to be Reliable in Harsh Environments
PCB Chat 131: Sergiy Nesterenko on AI-Driven PCB Design
RM 143: A Candid Conversation with Doug Pauls
PCB Chat 130: Audrey McGuckin on Developing Leadership Skills
RM 142: Live from SMTA's Pan Pacific Strategic Electronics Symposium (PanPac)
RM 141: Component Tape Splicing Best Practices
PCB Chat 129: Electronics Design Market Update with Wally Rhines
PCB Chat 128: The Latest HDP Consortium Projects
RM 139: Environmentally Responsible Alternatives to Traditional PCB Fabrication
PCB Chat 127: Matthias Wagner on AI-Based PCB Design Tools
RM 138: Hand Soldering and Rework Best Practices
RM 137: Building a Sustainable Career with a Sustainable Impact
PCB Chat 127: David Schild on US Strategy for Supply Chain Readiness
PCB Chat 126: Andrew Scheuermann on AI in Electronics
RM 136: Environmentally Responsible/Sustainable Conformal Coating
PCB Chat 125: Manny Marcano on Spinoff of Accelerated Designs
PCB Chat 124: Wally Rhines on the Latest PCB Design Software Market Data
RM 135: Zach Peterson about Board Design Best Practices
RM 134 -- 2023 Podcast Season Wrap-Up
RM 133: Novel Wireless / Wearable ESD Monitoring